Investigation of Shear Behaviour of Rock Joints under Cyclic Loading
thesis
posted on 2024-11-18, 08:21authored byMairaj Hyder Alias Aamir Soomro
Mechanical behaviour of a rock mass is significantly affected by the occurrence of inherent discontinuities (such as joints, fractures, bedding planes, etc.), therefore comprehensive knowledge of the effect of such discontinuities is necessary for the safe and economic design of geo-structures in or on a rock mass. Generally, the typical shear behaviour of a rock joint has been investigated under monotonic loading conditions, ignoring the fact that most of the time the structures embedded in a rock mass are subjected to cyclic loads, and it is likely that such structures fail to sustain the induced stresses from these cyclic loads (e.g., freight or passenger trains, seismic events or mining operations) because all the current standards for designing structures are based on analyses conducted under static loading conditions. The aim of this research was to experimentally investigate the effect of cyclic loading on the shear behaviour of natural rough rock joints under triaxial loading conditions and direct shear loading conditions, to semi-analytically model the shear behaviour of rock joints incorporating the influence of cyclic loading and to extend Sakurai’s (1977) concept of critical strain to the domain of rock joints considering the effect of cyclic loading. To achieve the aims of this study, several aspects of the shear behaviour of rock joints under cyclic triaxial and cyclic direct shear loading were studied. The experiments were conducted under cyclic triaxial and direct shear loading condition using GDS ELDYN triaxial apparatus and UOW servo-controlled direct shear equipment. Two different types of specimens were selected for both types of testing. The surface roughness characterization was performed using a non-contact 3D scanner (VIVID910) on each type of specimen, and the joint roughness coefficient (JRC) was evaluated as 12.6 and 7.2 for triaxial test specimens, and 11.7 and 8.1 for direct shear test specimens. For the cyclic triaxial tests, the test specimens were subjected to a cyclic deviatoric stress of 200 kPa and 300 kPa at a frequency of 8Hz with a varying number of loading cycles under confining pressures of 10 kPa, 20 kPa and 30 kPa. For the cyclic direct shear tests, the test specimens were sheared under constant normal load (CNL) and constant normal stiffness (CNS) boundary conditions at an initial normal stress of 0.25 MPa, 0.50 MPa, and 1.0 MPa, representing the typical insitu stress conditions observed in the field. The shear rate for the cyclic direct shear experiments was considered as 6 mm/min, 20 mm/min, and 40 mm/min. The laboratory experiments under triaxial loading conditions revealed that the shear strength of a rock joint is significantly reduced with an increasing number of loading cycles, and a drop in shear strength continued until residual shear strength was achieved. In addition, based on experimental results, two zones were identified when considering the normalized joint degradation ratio (KJDR); a zone of asperity interference where shear strength was controlled by surface roughness asperities, and a zone of asperity non-interference where the effect of asperities on shear strength of rock joint was insignificant. The experimental results using direct shear equipment highlighted that the shear strength and dilatant behaviour of rock joint decreases with the increasing number of shear cycles. Unlike constant normal load (CNL) where the applied initial normal stress remains constant throughout the shearing process, the variation in normal stress was observed under constant normal stiffness (CNS) boundary conditions. The surface roughness damage was more pronounced under CNS, however severe damage was observed at higher level of initial normal stress. New rock joint models were developed to evaluate the shear strength and critical shear strain of rock joints, considering the effect of cyclic loading. It was observed from the experimental results that the shear strength and critical shear strain of rock joint is suppressed with increasing number of loading cycles until a threshold limit value has been achieved and beyond which the variation was found insignificant. The newly developed critical shear strain model was used to elucidate the sliding potential of rock joint. Based on this, a new index to classify the sliding potential of rock joint, called Joint Sliding Potential (JSP), has been proposed to characterize the cyclic loading induced sliding instability of rock joint.
History
Year
2022
Thesis type
Doctoral thesis
Faculty/School
School of Civil, Mining and Environmental Engineering
Language
English
Embargo release date
2025-01-02
Disclaimer
Unless otherwise indicated, the views expressed in this thesis are those of the author and do not necessarily represent the views of the University of Wollongong.